Page 1 of 2 12 LastLast
Results 1 to 10 of 19

Thread: Amplifier wire termination suggestions.

  1. Back To Top    #1

    Amplifier wire termination suggestions.

    I was wondering what everyone’s preferred method is when it comes to the wire terminals at the amps?

    Wire ferrules, some kind of adapter, bare wire, etc.

    What about speaker wire pants? I’ve seen them used in home audio but not so much in car audio.

    I want this install to be safe and look clean and I’m having trouble with stray strands of wire that look like crap. My other amps have had deeper terminals or plastic shields around the terminals. These new amps have neither.



    Sent from my iPhone using Tapatalk Pro

  2. Back To Top    #2
    Refuses to grow up... mumbles's Avatar
    Real Name
    Eric
    Location
    ATL
    Posts
    285
    Join Date
    Sep 2016

    Re: Amplifier wire termination suggestions.

    Yeah, stray strands can be a real problem and thats why I used color coded ferrules in my last install. I also used speaker pants, but all my wiring was on the underside of the amp board, and all you could see was the last 3" of each run, so speaker pants just added a bit of a cool factor.

  3. Back To Top    #3
    Senior Member chithead's Avatar
    Real Name
    Daniel
    Location
    Concord,NC
    Vehicle
    We don't talk about it
    Posts
    3,058
    Join Date
    Jul 2013

    Re: Amplifier wire termination suggestions.

    You could tin the very ends with solder just to keep all them strays in check. Still allows some crush factor to the wire when tightening them screws.
    Are you not entertained?!?!


  4. Back To Top    #4
    Refuses to grow up... mumbles's Avatar
    Real Name
    Eric
    Location
    ATL
    Posts
    285
    Join Date
    Sep 2016

    Re: Amplifier wire termination suggestions.

    Quote Originally Posted by chithead View Post
    You could tin the very ends with solder just to keep all them strays in check. Still allows some crush factor to the wire when tightening them screws.
    I've never had much luck tinning with anything larger than 4 gauge...

  5. Back To Top    #5
    Senior Member chithead's Avatar
    Real Name
    Daniel
    Location
    Concord,NC
    Vehicle
    We don't talk about it
    Posts
    3,058
    Join Date
    Jul 2013

    Re: Amplifier wire termination suggestions.

    Ohhhh! That's a great point. Yes sir, I agree, it mostly works for just speaker gauge wires up to about 8ga. Not so great for 4ga or larger.
    Are you not entertained?!?!


  6. Back To Top    #6
    Perpetually dissatisfied tRidiot's Avatar
    Real Name
    Danny
    Location
    Oklahoma
    Posts
    203
    Join Date
    Aug 2013

    Re: Amplifier wire termination suggestions.

    Here's what I did.

    Name:  20190727_182906-X4.jpg
Views: 619
Size:  730.6 KB

  7. Back To Top    #7
    Owner BigAl205's Avatar
    Real Name
    Alan
    Location
    Hayden, AL
    Vehicle
    2018 Chevy Silverado Z-71
    Posts
    5,343
    Join Date
    Feb 2013

    Re: Amplifier wire termination suggestions.

    You just need a better soldering iron

  8. Back To Top    #8

    Re: Amplifier wire termination suggestions.

    I tried using ferrules for the first time with my JL Audio XD600/6V2 amp. I had issues though - they actually caused issues with the "clamps" used by JL Audio for the speaker wires. All seemed fine until I went to remove the speaker wires. I found that the top part of the "wire clamp" (not sure what the technical name is - it's a flat piece of metal that pushes down onto the wires as you tighten them) actually came off completely! This happened on multiple channels. It seems that the ferrules were just a little too "stiff" for the type of connections on the JL amp.

    I guess there is a reason why JL specifically says "bare wires" in the owners manual. :-)

    So I'd be careful with ferrules when certain types of amps!

  9. Back To Top    #9

    Re: Amplifier wire termination suggestions.

    I might practice soldering some scrap 4 gauge wire this weekend. I’d have to order some ferrules for wire that size, but I might like to have them in case the solder doesn’t work out.


    Sent from my iPhone using Tapatalk Pro

  10. Back To Top    #10
    Noob el_bob-o's Avatar
    Real Name
    Bob
    Location
    Fort Worth, TX
    Vehicle
    2005 GMC Sierra ExtCab SLT Z71
    Posts
    14
    Join Date
    Sep 2014

    Re: Amplifier wire termination suggestions.

    I recently swapped one of my Eclipse amps that uses spades for an old Boston Acoustics amp that is just a hex screw into bare wire. For speaker wire I was having issues getting the 16 gauge to stay secure with bare wire so it was either 12 gauge for my mids and tweeters or ferules. I ordered this cheap kit from Amazon:


    Ferrule Crimping Tool Kit, Preciva

    They are very soft and not great for disconnecting and reconnecting but they work really well for holding firmly. The power and ground connections are setup to accept 2 8 gauge wires each, not sure why but I assume for size reasons. I use 4 gauge to 8 gauge reducers for those so that I only need one of each.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Back To Top