Page 3 of 3 FirstFirst 123
Results 21 to 25 of 25

Thread: INCREASE MID BASS! How to Sound Deaden Like a Pro

  1. Back To Top    #21
    Owner BigAl205's Avatar
    Real Name
    Alan
    Location
    Hayden, AL
    Vehicle
    2018 Chevy Silverado Z-71
    Posts
    5,343
    Join Date
    Feb 2013

    Re: INCREASE MID BASS! How to Sound Deaden Like a Pro

    I've used galvanized sheet metal and self-tapping screws covered in CLD and filled any gaps with duct seal

    https://www.lowes.com/pd/Gardner-Ben...t-Seal/4595233

  2. Back To Top    #22

    Re: INCREASE MID BASS! How to Sound Deaden Like a Pro

    seems like someone with a 3-D scanner could create files of the doors of most popular vehicles, then you take the file/ download to your local library/3-D printer space, and voila....

    for a small fee and the cost of a spool of resin one could have custom fitted door seal panels, probably would be better to engineer into the panel some structural rigidity, like honeycomb or whatever, then let the 3-D printer do all that hard work, leaving lightweight panels with bracing built-in, ready for install with screw holes already part of the piece.

    might be a bit too fancy for shoring up door work, mid bass isn't that important anyway... if no one is going to see it anyway.

  3. Back To Top    #23
    Noob Babs's Avatar
    Location
    Asheville NC
    Vehicle
    Civic Si Sedan
    Posts
    717
    Join Date
    Mar 2014

    Re: INCREASE MID BASS! How to Sound Deaden Like a Pro

    From my log finally attempting a good job at sealing.. I used .020 aluminum sheet, full-coverage with CLD, to fill the hole what I could and CCF where it wasn't terribly feasible over the window motor. Inside was treated with layer of moisture-covered Owens Corning 703. CLD coverage over every hole that could be covered also. Basically the window slit and where doorcard attachment pin holes are, are the only unsealed areas. A CCF and MLV layer between the card and door metal, along with existing CLD on door metal remained. Then insulation actually in the voids of the door card itself, as well as FAST rings round the driver. Easily the single best thing I've done this year in terms of improving speaker response. Flat out worked. Fixed huge phase-related voids from backwave interference etc. I can't speak highly enough of a good job sealing a door.






    2008 Civic Si Sedan
    Build Log
    You measure with REW? Consider donating. I did

  4. Back To Top    #24
    ~Paw~Paw})]<^>¥ Hic's Avatar
    Real Name
    Hic
    Location
    Michigan
    Vehicle
    99 Contour SVT
    Posts
    3,124
    Join Date
    Jul 2013

    Re: INCREASE MID BASS! How to Sound Deaden Like a Pro

    NICE JOB !
    Viewing Smilies , you trying to access privileged system?¤Somewhere 0ut There¤}]

  5. Back To Top    #25
    ~Paw~Paw})]<^>¥ Hic's Avatar
    Real Name
    Hic
    Location
    Michigan
    Vehicle
    99 Contour SVT
    Posts
    3,124
    Join Date
    Jul 2013

    Re: INCREASE MID BASS! How to Sound Deaden Like a Pro

    Either multiples of smaller drivers or two big uns [ 10's / 12's ] ought to put down some mid-bass !
    Viewing Smilies , you trying to access privileged system?¤Somewhere 0ut There¤}]

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Back To Top