Results 1 to 7 of 7

Thread: REW 'Match response to target' help

  1. Back To Top    #1

    REW 'Match response to target' help

    Every time I try to Auto EQ in REW I presented an error dialog that says "The match range doesn't overlap the range of measurement".
    I assume the match range is 20-200 in this screenshot but where is the range of measurement at that I am not matching?

    Click image for larger version. 

Name:	rew-shot.jpg 
Views:	133 
Size:	221.5 KB 
ID:	17808

  2. Back To Top    #2
    Wave Shepherd - aka Jazzi Justin Zazzi's Avatar
    Location
    Northridge, CA
    Posts
    670
    Join Date
    Aug 2018

    Re: REW 'Match response to target' help

    Try adjusting the values in the lower right corner in the filter tasks section?

    Or, you could share your REW save file an let someone tinker with it to see what they can find?
    Measure with mics, mark with chalk, cut with torch, grind to fit, sand to finish, paint to match.
    Updated Justin tuning sheet (Justin and Erica tuning companion for SMAART and REW)
    Do it for them.

  3. Back To Top    #3

    Re: REW 'Match response to target' help

    I have played with all kinds of different values. Sometimes a measurement works and sometimes it doesn't.

    There has to be something simple that I am doing wrong.

  4. Back To Top    #4

    Re: REW 'Match response to target' help

    I just tried to auto eq sub signal and it worked fine this time. I don't understand what the heck is going on.

    Here are the measurements:

  5. Back To Top    #5
    Noob Cathul's Avatar
    Real Name
    Peter
    Location
    Leipzig, Germany
    Vehicle
    Ford Mustang GT Premium
    Posts
    136
    Join Date
    Apr 2020

    Re: REW 'Match response to target' help

    I have this error sometimes as well. When changing from 1/48 smoothing to 1/24 smoothing this error dissappears for whatever reason.
    SYNC3 headunit
    Mosconi Pico 8/10 DSP
    Mosconi D2 500.1
    Gladen Zero Pro 165.3 DC
    JL Audio 10w3v3 in custom enclosure (Blueprint by Mark @Caraudiofabrication)

  6. Back To Top    #6
    Noob swrocket's Avatar
    Location
    Vaughan, ON
    Vehicle
    2021 Camaro 2SS
    Posts
    56
    Join Date
    Aug 2020

    Re: REW 'Match response to target' help

    I downloaded your measurements and had no issues...
    here is the auto eq for the "left" measurement.
    Click image for larger version. 

Name:	cajeq.jpg 
Views:	110 
Size:	323.2 KB 
ID:	17819

    and here is the "right"
    Click image for larger version. 

Name:	cajeqright.jpg 
Views:	95 
Size:	324.1 KB 
ID:	17820

    If you are working on only one driver, or some part of the curve other than the whole curve, you should use "Speaker Driver" as the target type and enter the HP and LP crossover points you desire, which should be the same ones you entered in Jazzi's spreadsheet to create the curves.

  7. Back To Top    #7

    Re: REW 'Match response to target' help

    I found that if I save the measurements, close the app, and re-open it works fine.

    I will try changing from 1/48 to 1/24 smoothing to see if that makes it work too.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Back To Top