Results 1 to 5 of 5

Thread: Gladen Mosconi DSP - how tos from Frank Miketta

  1. Back To Top    #1
    Noob Cathul's Avatar
    Real Name
    Peter
    Location
    Leipzig, Germany
    Vehicle
    Ford Mustang GT Premium
    Posts
    136
    Join Date
    Apr 2020

    Gladen Mosconi DSP - how tos from Frank Miketta

    Dear all,

    i just found a lot of how-tos for the Gladen Mosconi DSPs held directly by their developer, Frank Miketta.
    They are on the Gladen Audio facebook side (if you use Facebook that is) and he has done a series of vides where he explains the Mosconi Gladen DSPs that use the new GUI including how to measure the car manufacturers stock headunit, set gains on the DSP, deequalize the inbound frequency response, check for allpass filters and time delay and how to correct them and stuff like that up to how to use the group eq, individual driver eq, allpass filters in the Mosconi DSPs, setting levels, use the group eq, center speaker mixer, rear fill and everything you can think about.

    It starts here: https://www.facebook.com/GladenAudio...7570367668250/
    From there you can follow the series of videos.
    And be aware, his english is not really the best, but here you get first hand information from the developer of those DSPs itself.

    The videos are valid for the Pico 6/8, Pico 8/12, the new Atomo 4to6, the 8to12 Aerospace, 6to8 Aerospace and 8to12 Pro.

    Just thought this might be of interest for some of you.
    SYNC3 headunit
    Mosconi Pico 8/10 DSP
    Mosconi D2 500.1
    Gladen Zero Pro 165.3 DC
    JL Audio 10w3v3 in custom enclosure (Blueprint by Mark @Caraudiofabrication)

  2. Back To Top    #2
    Wave Shepherd - aka Jazzi Justin Zazzi's Avatar
    Location
    Northridge, CA
    Posts
    670
    Join Date
    Aug 2018

    Re: Gladen Mosconi DSP - how tos from Frank Miketta

    Are there any non-fb videos?
    Measure with mics, mark with chalk, cut with torch, grind to fit, sand to finish, paint to match.
    Updated Justin tuning sheet (Justin and Erica tuning companion for SMAART and REW)
    Do it for them.

  3. Back To Top    #3
    Noob Cathul's Avatar
    Real Name
    Peter
    Location
    Leipzig, Germany
    Vehicle
    Ford Mustang GT Premium
    Posts
    136
    Join Date
    Apr 2020

    Re: Gladen Mosconi DSP - how tos from Frank Miketta

    Look on YouTube for his channel. Frank Miketta.
    SYNC3 headunit
    Mosconi Pico 8/10 DSP
    Mosconi D2 500.1
    Gladen Zero Pro 165.3 DC
    JL Audio 10w3v3 in custom enclosure (Blueprint by Mark @Caraudiofabrication)

  4. Back To Top    #4
    Noob Cathul's Avatar
    Real Name
    Peter
    Location
    Leipzig, Germany
    Vehicle
    Ford Mustang GT Premium
    Posts
    136
    Join Date
    Apr 2020

    Re: Gladen Mosconi DSP - how tos from Frank Miketta

    Yesterday evening Frank Miketta showed the "last" part of the new software for the newer and more capable DSP units from Mosconi, but it was on Facebook only, not on Youtube (yet).
    Mosconi Phase Control.
    Apparently the software is even able to correct the phase between drivers in 1° steps and even automaticly f.e. for phase between tweeter and midbass.
    This new part of the software will be available this week afaik.

    If interested check the Gladen Audio facebook page and watch for yourself.
    SYNC3 headunit
    Mosconi Pico 8/10 DSP
    Mosconi D2 500.1
    Gladen Zero Pro 165.3 DC
    JL Audio 10w3v3 in custom enclosure (Blueprint by Mark @Caraudiofabrication)

  5. Back To Top    #5
    Senior Member
    Location
    Scottsdale
    Vehicle
    2015 Armada
    Posts
    174
    Join Date
    May 2020

    Re: Gladen Mosconi DSP - how tos from Frank Miketta

    Deleted post as i was just being pissy and not adding to the conversation
    Last edited by Cutaway; 06-02-2020 at 07:37 PM.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Back To Top