Page 10 of 40 FirstFirst ... 8910111220 ... LastLast
Results 91 to 100 of 394

Thread: New Build - 2019 JL Wrangler 2 door

  1. Back To Top    #91
    Senior Member jrwalte's Avatar
    Location
    Atlanta
    Vehicle
    2007 Corolla
    Posts
    293
    Join Date
    Oct 2019

    Re: New Build - 2019 JL Wrangler 2 door

    Looks nice. I'd go ahead and spray coat that ground connection to prevent rust. While doing it might as well spray each screw for the power wire clamps.

  2. Back To Top    #92

    Re: New Build - 2019 JL Wrangler 2 door

    add a jam nut to the ground
    Last edited by nadams5755; 01-22-2020 at 10:30 PM.

  3. Back To Top    #93

    Re: New Build - 2019 JL Wrangler 2 door

    Quote Originally Posted by jrwalte View Post
    Looks nice. I'd go ahead and spray coat that ground connection to prevent rust. While doing it might as well spray each screw for the power wire clamps.
    That's a good idea... I did use stainless steel on everything, but still...

    Quote Originally Posted by nadams5755 View Post
    add a jam nut to the ground
    Good point. I tightened the nut with an impact!
    2019 Jeep Wrangler 2 Door - Morel Elate 3 way, Mmats HiFi 6150 & M2000.2, Hutchinson NDFEB 10", MiniDSP w/DL, Fiio X5

    #TRUMP2020

  4. Back To Top    #94
    Senior Member Smitty's Avatar
    Location
    FL
    Vehicle
    2019 Toyota 4Runner, 2019 Toyota Camry
    Posts
    271
    Join Date
    Oct 2019

    Re: New Build - 2019 JL Wrangler 2 door

    Very interesting cable run. What wrap did you use?
    Meh, it'll play.

  5. Back To Top    #95

    Re: New Build - 2019 JL Wrangler 2 door

    Quote Originally Posted by Smitty View Post
    Very interesting cable run. What wrap did you use?
    Thanks!

    I did it kinda ass-backwards, first I did a Techflex sleeve and then wrapped it in the heat resistant Tesa tape. I wanted the utmost protection from the elements, abrasion and heat.

    The power wire runs along the top of the frame with a combination of zip ties and cable clamps...
    2019 Jeep Wrangler 2 Door - Morel Elate 3 way, Mmats HiFi 6150 & M2000.2, Hutchinson NDFEB 10", MiniDSP w/DL, Fiio X5

    #TRUMP2020

  6. Back To Top    #96

    Re: New Build - 2019 JL Wrangler 2 door

    Nice Ride man.

  7. Back To Top    #97

    Re: New Build - 2019 JL Wrangler 2 door

    Finally had a little time!

    Here is a comparison of the factory pod vs the Metra. Unfortunately, the Metra is slightly smaller than the factory one, but it's my only option... There is no way the factory one could be made to hold a 6.5".






    I cut a hole and epoxied in the aperiodic vent.







    Rough cut for the 1/2" birch plywood baffle

    2019 Jeep Wrangler 2 Door - Morel Elate 3 way, Mmats HiFi 6150 & M2000.2, Hutchinson NDFEB 10", MiniDSP w/DL, Fiio X5

    #TRUMP2020

  8. Back To Top    #98

    Re: New Build - 2019 JL Wrangler 2 door

    Btw, I have seen a few videos and read instructions on how to remove the driver side speaker pod on the JL, and they all say that you need to disassembled most of the dash. This is absolutely not true. I removed my pod quite easily by taking out a few of the screws and simply pulling the lower dash panel back enough to drop the pod out. Very similar to how it's done on the JKs...
    2019 Jeep Wrangler 2 Door - Morel Elate 3 way, Mmats HiFi 6150 & M2000.2, Hutchinson NDFEB 10", MiniDSP w/DL, Fiio X5

    #TRUMP2020

  9. Back To Top    #99

    Re: New Build - 2019 JL Wrangler 2 door

    nice have you figured out the air volume on those yet?

  10. Back To Top    #100

    Re: New Build - 2019 JL Wrangler 2 door

    Quote Originally Posted by toneloc2 View Post
    nice have you figured out the air volume on those yet?
    Not yet, I forgot... I'll do it on the passenger side, which I won't get to until next week.
    2019 Jeep Wrangler 2 Door - Morel Elate 3 way, Mmats HiFi 6150 & M2000.2, Hutchinson NDFEB 10", MiniDSP w/DL, Fiio X5

    #TRUMP2020

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Back To Top