Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 28

Thread: 2017 Chevy Spark build

  1. Back To Top    #11
    Senior Member chithead's Avatar
    Real Name
    Daniel
    Location
    Concord,NC
    Vehicle
    We don't talk about it
    Posts
    3,052
    Join Date
    Jul 2013

    Re: 2017 Chevy Spark build

    For Focal? VERY nice! And a 12TW3? Perfect setup right there. I like the layout with the AudioControl in the middle myself, might be more difficult for cable routing though.
    Are you not entertained?!?!


  2. Back To Top    #12
    ~Paw~Paw})]<^>¥ Hic's Avatar
    Real Name
    Hic
    Location
    Michigan
    Vehicle
    99 Contour SVT
    Posts
    3,164
    Join Date
    Jul 2013

    Re: 2017 Chevy Spark build

    Quote Originally Posted by Keele81 View Post
    Oh, & it looks like my 12tw3 might be a freebie. Waited weeks for it to show up, never did.
    Score!
    USPS, FedEx, UPS ?
    Viewing Smilies , you trying to access privileged system?¤Somewhere 0ut There¤}]

  3. Back To Top    #13
    Noob Keele81's Avatar
    Real Name
    Keele
    Location
    So. IL
    Vehicle
    17 Spark
    Posts
    150
    Join Date
    Jun 2013

    Re: 2017 Chevy Spark build

    I liked the middle as well, symmetrical lol The Focals are a funny story, was giving a few long time gamer friends hell about missing my birthday & I'd still take gifts. Frenchie looked up the Focals & laughed cause I said they're expensive & it was ≈$125 US at places they're familiar with. Bought two & shipped them to me at cost

  4. Back To Top    #14
    Noob Keele81's Avatar
    Real Name
    Keele
    Location
    So. IL
    Vehicle
    17 Spark
    Posts
    150
    Join Date
    Jun 2013

    Re: 2017 Chevy Spark build

    The subs a bad decision eBay purchase, knew better but the pennies saved tempted me too much. Waited well past time it was due to arrive, seller never replies or shipped so they refunded me. Week later I got a notification it's been picked up by FedEx & is in route

  5. Back To Top    #15
    Noob Keele81's Avatar
    Real Name
    Keele
    Location
    So. IL
    Vehicle
    17 Spark
    Posts
    150
    Join Date
    Jun 2013

    Re: 2017 Chevy Spark build

    Cable routing I'd planned to make a little easier by doing a riser between mounting surface for amps & lci & a base plate below. Run some wiring underneath & pass through holes or a milled slot. If that makes sense lol

  6. Back To Top    #16
    Noob Keele81's Avatar
    Real Name
    Keele
    Location
    So. IL
    Vehicle
    17 Spark
    Posts
    150
    Join Date
    Jun 2013

    Re: 2017 Chevy Spark build

    3 doors wired up & deadened, little bit of progress

    Sent from my Pixel using Tapatalk

  7. Back To Top    #17
    Noob Keele81's Avatar
    Real Name
    Keele
    Location
    So. IL
    Vehicle
    17 Spark
    Posts
    150
    Join Date
    Jun 2013

    Re: 2017 Chevy Spark build

    Dropped the wire bundle in the pillars, clipped speaker leads, & soldered 18 gauge to go to LC7I & 16 gauge to the other side for mids to amp. Had to add a 16 gauge run in to rear doors for tweeters as well. Luckily I was able to pass them around the molex easy enough. Wrapped everything with Tesa tape, & will techflex from where it exits carpet on.. for bonus hp, or whatever lol

    Sent from my Pixel using Tapatalk

  8. Back To Top    #18
    Noob Keele81's Avatar
    Real Name
    Keele
    Location
    So. IL
    Vehicle
    17 Spark
    Posts
    150
    Join Date
    Jun 2013

    Re: 2017 Chevy Spark build

    A-pillars back in, tweeters high temp hot glued into trimmed factory mounts. Have a slight angle on them instead of completely off axis, half assed aimed center

    Trimmed surrounding raised area, removed grills, & good enough for me. The pointless hidden techflex screams I'm bored lol

    Sent from my Pixel using Tapatalk

  9. Back To Top    #19
    Noob Keele81's Avatar
    Real Name
    Keele
    Location
    So. IL
    Vehicle
    17 Spark
    Posts
    150
    Join Date
    Jun 2013

    Re: 2017 Chevy Spark build

    Chassis grounds done, pos to fuse holders done, need to techflex back half of pos runs up to the firewall & fuse my 16 gauge primary run still

    Sent from my Pixel using Tapatalk

  10. Back To Top    #20
    Noob Keele81's Avatar
    Real Name
    Keele
    Location
    So. IL
    Vehicle
    17 Spark
    Posts
    150
    Join Date
    Jun 2013

    Re: 2017 Chevy Spark build

    Used 1/4 abs for the fuse holder mount. Caught 2 factory holes that we're being used luckily

    Sent from my Pixel using Tapatalk

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Back To Top