Page 8 of 10 FirstFirst ... 678910 LastLast
Results 71 to 80 of 98

Thread: Toyota 4Runner SQ rebuild - Audible Physics, Zapco, OnCore

  1. Back To Top    #71
    Clueless lowcel's Avatar
    Real Name
    Bruce
    Location
    Charleston, WV
    Vehicle
    4Runner & Altima Coupe
    Posts
    172
    Join Date
    Apr 2017

    Re: Toyota 4Runner SQ rebuild - Audible Physics, Zapco, OnCore

    One less thing to do this weekend, the Shrockworks second battery tray is installed. Had to move the power steering fluid reservoir and a little AC line. Not too bad of a job.




    I've got a budget of $1,000. That should be more than enough.

  2. Back To Top    #72
    Clueless lowcel's Avatar
    Real Name
    Bruce
    Location
    Charleston, WV
    Vehicle
    4Runner & Altima Coupe
    Posts
    172
    Join Date
    Apr 2017

    Re: Toyota 4Runner SQ rebuild - Audible Physics, Zapco, OnCore

    It's always good to have a plan right?


    Friday:



    • Sound deaden the floor from back seats forward. 3 hours
    • Install black hole tile in front doors. Apply MX-4 deadener to doors. Install speakers. 2 hours




    Saturday



    • Remove old wire. Run all new power, ground, remote, speaker wires, RCA's, and optical. 8 hours
    • Install a-pillars. 1 hour




    Sunday



    • Install CD Changer. 1 hour
    • Hook up head unit and dsp, get steering wheel controls working. 3 hours
    I've got a budget of $1,000. That should be more than enough.

  3. Back To Top    #73
    Clueless lowcel's Avatar
    Real Name
    Bruce
    Location
    Charleston, WV
    Vehicle
    4Runner & Altima Coupe
    Posts
    172
    Join Date
    Apr 2017

    Re: Toyota 4Runner SQ rebuild - Audible Physics, Zapco, OnCore

    I left work a little early today to get a little work done. I added additional sound deadening to my doors, switched out my speakers to some new ones, and ran a new speaker wire in each door.


    I started by putting some Sound Barrier MX-4 on the bar behind the speakers.








    Next I installed almost 1/2 a box of Black Hole Tiles in each door.






    I attempted to checker board them everywhere except directly behind the speakers.





    Next I put a layer of Sound Barrier MX-4 on each door.





    Next, Knu OFC wires.






    Last but not least, I installed the new Audible Physics Brahma 6W's.





    One bonus picture, my new Brahma 6W and V2.


    I've got a budget of $1,000. That should be more than enough.

  4. Back To Top    #74
    Senior Member chithead's Avatar
    Real Name
    Daniel
    Location
    Concord,NC
    Vehicle
    We don't talk about it
    Posts
    3,052
    Join Date
    Jul 2013

    Re: Toyota 4Runner SQ rebuild - Audible Physics, Zapco, OnCore

    Those are some great looking drivers, can't wait to read your review of them!
    Are you not entertained?!?!


  5. Back To Top    #75
    Clueless lowcel's Avatar
    Real Name
    Bruce
    Location
    Charleston, WV
    Vehicle
    4Runner & Altima Coupe
    Posts
    172
    Join Date
    Apr 2017

    Re: Toyota 4Runner SQ rebuild - Audible Physics, Zapco, OnCore

    I took a short video of the door sound deadening "tap test". I've never heard anything like it.



    So far today I've managed to finish up the sound deadening, for now at least. I plan to put a layer of Sound Barrier MX-4 on the back three doors later on.

    Before...



    Now...


    I've got a budget of $1,000. That should be more than enough.

  6. Back To Top    #76
    Clueless lowcel's Avatar
    Real Name
    Bruce
    Location
    Charleston, WV
    Vehicle
    4Runner & Altima Coupe
    Posts
    172
    Join Date
    Apr 2017

    Re: Toyota 4Runner SQ rebuild - Audible Physics, Zapco, OnCore

    I hate wiring up a system. I worked 8-1/2 hours today and didn't get everything hooked up. Still have to run power wire, RCA's, hook up distribution blocks, hook up head unit, DSP and hook up batteries.

    I think installing techflex and heatshrink makes the job take twice as long.







    I applied a drop of CA glue to all of the zip tie holders to make sure they stay in place.

    I've got a budget of $1,000. That should be more than enough.

  7. Back To Top    #77
    Clueless lowcel's Avatar
    Real Name
    Bruce
    Location
    Charleston, WV
    Vehicle
    4Runner & Altima Coupe
    Posts
    172
    Join Date
    Apr 2017

    Toyota 4Runner SQ rebuild - Audible Physics, Zapco, OnCore

    I worked outside in the heat doing wiring from 7:30 am until 3:00 pm again today. That's not easy on a fat boy. I'm getting closer though.

    Head unit wires up. Everything soldered and covered with heat shrink. I'm getting power for the head unit from a distribution block in the rear of the vehicle with OFC 12 gauge wires.



    Wires all routed to keep power away from signal cables. The cable tie downs all received a drop of CA glue and spaced at 6" to 7" apart. All wires are protected with Techflex except the head unit power wires because they are very well protected in their insulation. I used KnuKonceptz KL3 Kable.







    I also managed to get my pillars installed. I had to remove the lower mount for the ole shit handle in order to fit the passenger side pillar. Totally worth it.





    Better picture of the pillars later but here's one to hold us over.



    For connectors for the 2's and tweets I used XT60 quick connects.





    My goal was to have it playing today. I fell short of my goal. So, I'm calling off work tomorrow.
    Last edited by lowcel; 06-11-2017 at 06:48 PM.
    I've got a budget of $1,000. That should be more than enough.

  8. Back To Top    #78
    Owner BigAl205's Avatar
    Real Name
    Alan
    Location
    Hayden, AL
    Vehicle
    2018 Chevy Silverado Z-71
    Posts
    5,699
    Join Date
    Feb 2013

    Re: Toyota 4Runner SQ rebuild - Audible Physics, Zapco, OnCore

    Wow, you're going whole-hog!

  9. Back To Top    #79
    Clueless lowcel's Avatar
    Real Name
    Bruce
    Location
    Charleston, WV
    Vehicle
    4Runner & Altima Coupe
    Posts
    172
    Join Date
    Apr 2017

    Re: Toyota 4Runner SQ rebuild - Audible Physics, Zapco, OnCore

    Quote Originally Posted by BigAl205 View Post
    Wow, you're going whole-hog!
    I'm trying my best.
    I've got a budget of $1,000. That should be more than enough.

  10. Back To Top    #80
    Noob JayinMI's Avatar
    Location
    Flushing, MI
    Vehicle
    2015 Mazda 6i Touring
    Posts
    598
    Join Date
    Oct 2014

    Re: Toyota 4Runner SQ rebuild - Audible Physics, Zapco, OnCore

    Quote Originally Posted by lowcel View Post
    I've got a budget of $1,500. That should be more than enough.
    I LOL'd. My deadener order is going to be something like $600, my order from Wirecare another $300. And I don't have a midsized SUV! lol

    Jay

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Back To Top