-
98 Civic
My son turns 16 in a few weeks. We picked this up from my brother in law a few weeks ago for $600 and my son is going to install the siding on his house. He's been working on my crew for a few years on weekends.
http://i95.photobucket.com/albums/l1...ps5xn6pc8m.jpg
It's spent it's entire life in the Buffalo area so it's extremely surprisingly rust free.
-
Re: 98 Civic
-
Re: 98 Civic
I have all the pics. I just have to load then to a host for this forum. Probably tomorrow.
-
Re: 98 Civic
-
Re: 98 Civic
Quote:
Originally Posted by
DavidRam
Nice! What's the plan??
l'm not spending any money on this. Obviously a few bucks but installing stuff I already have. Just giving him a starter system.
2 way + sub.
Purchased used for $100
Dayton 408 + BT module
Already had this but upgraded
Samsung Tab A 2019
Bought these to try in my Maxima a couple years ago.
Vifa 1"- basically these but older
[URL unfurl="true"]https://www.madisoundspeakerstore.com/vifa-soft-dome-tweeters/vifa-bc25sc55-04-1-textile-dome-tweeter-truncated/[/URL]
Had these in my Maxima
Stereo Integrity TM65MKII
Bought these for my Astro Van
2 GRS 10SW-2 subs
Toro Rage Micro amps
Subs - MR2
Front stage - MRx4
They are tiny!
http://i95.photobucket.com/albums/l1...psfupsbhuf.jpg
http://i95.photobucket.com/albums/l1...psegxwi97i.jpg
I already own all the wiring, fusing, and such.
-
Re: 98 Civic
I started with the wiring. Ran the wiring under the door sill trim. No pics we know what that looks like. The added a breaker and upgraded the battery ground.
Found a hole already there. Just added a grommet.
http://i95.photobucket.com/albums/l1...psuhf02ouq.jpg
http://i95.photobucket.com/albums/l1...psolwzakge.jpg
I ran all the wires under the sill trim.
The door wires were suprisingly difficult.
The factory just had two grommets one on the car and one on the door. They ran the wires and electrical taped the rest. So I replaced the the tape with some 3m Super 88 and reused the grommets.
http://i95.photobucket.com/albums/l1...psw9iffi5b.jpg
The passenger side was ridiculous. I had to remove the entire HVAC system to get the wire in to the door.
This is where the glove box and HVAC were.
http://i95.photobucket.com/albums/l1...psbtna0iy8.jpg
http://i95.photobucket.com/albums/l1...ps0jaxjohl.jpg
-
Re: 98 Civic
Installed the TM65's. Just a trim ring and Resonix CCF. Not doing anything extra. I'll let my son upgrade deadening/speakers, install down the road.
Took the door panel off hoping I could just use the factory mounting. Had that rusty looking orange ring on the plastic door panel. There wasn't anything wrong just discolored.
I was able to trim the mounting plastic out of the way so I could sneak the TM65 past it.
http://i95.photobucket.com/albums/l1...ps3paxlemo.jpg
http://i95.photobucket.com/albums/l1...ps5ierijpd.jpg
I was able to cut a nice hole with some hand snipes.
http://i95.photobucket.com/albums/l1...psn5ggnxze.jpg
Some butyl rope to even out the door and seal up the mounting ring.
http://i95.photobucket.com/albums/l1...psz8lhmmq9.jpg
Smoothered in dielectric grease for corrosion protection.
http://i95.photobucket.com/albums/l1...psfsori3dw.jpg
Resonix CCF and mounted up.
http://i95.photobucket.com/albums/l1...psyrmo3byi.jpg
http://i95.photobucket.com/albums/l1...psjuctevyw.jpg
http://i95.photobucket.com/albums/l1...psy8hpswuz.jpg
http://i95.photobucket.com/albums/l1...psgnc2prge.jpg
-
Re: 98 Civic
Tweets are going on the dash in pods. I was going to make fiberglass pods. I started to use some clay to make a mold but I had it in dash I thought why not just make a clay pod. So I did. Finished shaping it, baked, sanded and filled.
http://i95.photobucket.com/albums/l1...ps0e8tsfiu.jpg
http://i95.photobucket.com/albums/l1...pstx3isby7.jpg
http://i95.photobucket.com/albums/l1...psuz6mqzmj.jpg
http://i95.photobucket.com/albums/l1...psusrfo1f2.jpg
-
Re: 98 Civic
I started to fiberglass a sub enclosure into the spare tier well. It's huge. 3.5 cuft. I used Johnson's wax as a mold release. Worked good as a release but discolored the resin and stunk up the car longer than the fiberglass.
http://i95.photobucket.com/albums/l1...psmeaa2f7z.jpg
http://i95.photobucket.com/albums/l1...pspx8wtntr.jpg
http://i95.photobucket.com/albums/l1...ps2nfwbdzl.jpg
Attached to wood
http://i95.photobucket.com/albums/l1...ps6otmzq1w.jpg
-
Re: 98 Civic
And so that glassing didn't work out. It didn't fit right so I just threw it out. I didn't feel like modifying it and waiting for multiple layers to dry. That would have took a couple days. So I rebuilt it with baltic birch.
http://i95.photobucket.com/albums/l1...psct66zoib.jpg
I still wanted my son to be able to easily remove the box if more space was needed. Skateboarding, snowboarding, biking, cases of beer, 9 teenagers in the car, etc. Whatever kids do. So I used hinges.
Under the CCF
http://i95.photobucket.com/albums/l1...psv8iakaiq.jpg
Covered the entire bottom in Resonix CCF
http://i95.photobucket.com/albums/l1...pslwvlnfct.jpg
Fits right in. One person job.
http://i95.photobucket.com/albums/l1...psy3v0kxtt.jpg
Amp tray lid is cut around the strut towers for added safety. Love my flexible rulers.
http://i95.photobucket.com/albums/l1...pssfyxoryv.jpg
http://i95.photobucket.com/albums/l1...psdljprgsa.jpg
Bolted the box through a plate in to the spare tire mount. The blue 1 1/2" dowels are bracing.
http://i95.photobucket.com/albums/l1...psruleeypi.jpg